Radon.org logo

Radon Mitigation: How Radon Reduction Systems Work and What They Cost

Radon mitigation lowers the radon level in a home. This guide explains how soil suction systems work, when EPA recommends fixing, how to find a qualified professional, and what EPA says about cost.

Last reviewed:

As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

Radon reduction systems work, and the right system depends on how your home is built. A qualified professional can design and install one, and a retest confirms that it is doing its job.

How a radon reduction system works

EPA generally recommends methods that prevent radon from entering the home. The most common is soil suction, also called active soil depressurization.

  1. Pipe. One or more suction pipes are inserted through the floor slab into the crushed rock or soil underneath, or sometimes installed from outside the home.
  2. Fan. A radon vent fan connected to the pipes draws radon gas from below the home. Common fan locations include attics, garages, and the exterior of the home.
  3. Vent. The pipe carries the gas to the air above the house, where it is quickly diluted.

EPA says some radon reduction systems can reduce radon levels by up to 99 percent, and that radon levels in most homes can be brought to 2 pCi/L or below. EPA does not recommend sealing cracks alone, because sealing alone has not been shown to lower radon levels significantly or consistently.

The fan runs all the time. Most soil suction systems include a warning device, usually a manometer, that shows whether the system is working. Fans may last five years or more, and EPA says replacing a fan costs around $200 to $350 including parts and labor, according to its radon FAQ (page last updated June 23, 2026, read November 21, 2026).

When EPA recommends fixing

EPA recommends fixing a home when the radon level is 4.0 pCi/L (150 Bq/m3) or higher. EPA also recommends considering a fix when the level is between 2 and 4 pCi/L.

Before you decide, confirm a high result with a follow-up test. Our radon testing guide lays out the EPA steps for short-term and long-term follow-up tests.

Hiring a qualified professional

EPA recommends that a qualified radon mitigation contractor fix your home, because lowering high radon levels takes specific technical knowledge and skills. Without the right equipment or knowledge, you could actually increase your radon level or create other hazards.

  • Start with your state. Contact your state radon program for a list of qualified professionals. Many states require radon professionals to be licensed, certified, or registered.
  • Find a qualified professional. EPA's page on finding a qualified radon service professional explains how to choose. EPA recognizes two national proficiency programs, NRPP and NRSB.
  • Follow the rules where you live. Any system must meet your state's requirements. In states without them, EPA recommends following its current voluntary consensus-based standards.
  • Compare estimates. Get estimates from one or more qualified contractors, and ask whether each includes diagnostic testing and a warning device.

Radon.org is an independent educational site. We are not a contractor, and we do not sell or install mitigation systems or recommend specific contractors.

What radon mitigation costs

EPA says most homes can be fixed for about the same cost as other common home repairs. EPA says your costs may vary depending on the size and design of your home and which radon reduction methods are needed, and advises you to get an estimate from one or more qualified radon mitigation contractors. This is EPA's statement from its radon FAQ (page last updated September 16, 2026, read November 21, 2026).

For the factors that affect a quote, see our radon mitigation cost guide and our guide to radon fans.

Radon fans we see listed

Listings for reference. Fan selection depends on system design; a qualified radon mitigation professional sizes the fan. See the radon fan sizing guide.

Retest after mitigation

EPA recommends testing again after the work is complete to confirm that radon levels have come down. EPA recommends that an independent, qualified radon tester do this test. The Consumer's Guide to Radon Reduction recommends a two-day to seven-day measurement, with windows and doors closed for 12 hours before and during the test, except for normal entry and exit.

Afterward, check the warning device regularly and consider retesting at least every two years. Retest when you start using a lower level of the home or finish a major renovation.

Frequently Asked Questions

Can I install a radon system myself?

EPA recommends hiring a qualified radon mitigation contractor. If you decide to do the work yourself, EPA suggests getting information on appropriate training courses from your state radon office first, since mistakes can raise radon levels or create other hazards.

Does sealing cracks in the foundation fix radon?

EPA does not recommend sealing alone. Sealing cracks and other openings is a basic part of most approaches to radon reduction, but by itself it has not been shown to lower radon levels significantly or consistently. A system with a vent pipe and fan is used in most cases.

How do I know my system is working?

Look at the warning device on a regular basis. Most soil suction systems include one, usually a manometer, and it shows whether the system is operating properly. The fan should never be turned off, and a retest at least every two years confirms that radon levels remain low.

What if my result is between 2 and 4 pCi/L?

The result is below the EPA action level, but EPA recommends considering a fix in that range. A qualified radon professional can explain your options and give an estimate, and your state radon program can help you find one.

Sources