Radon.org logo

Radon Fan Not Working: Troubleshooting and Warning Signs

A short, safe checklist if your radon fan seems quiet, noisy or off, and a clear line on what to leave to a professional.

Last reviewed:

As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

If your radon system's warning device looks different, or the fan sounds wrong or has gone silent, start with a few safe checks and then call a qualified mitigator. This page covers what you can look at from the floor, what not to touch, and why you should retest after any repair.

Why a working fan matters

In an active soil suction system the fan runs all the time. EPA says the fan should never be turned off and must run continuously for the system to work correctly. If the fan stops, the system is no longer drawing soil gas from beneath the home, so radon levels in the home may return to where they were before. A calm, step-by-step check is the right response, and a professional is the right person to fix it.

A homeowner checklist

  1. Look at the warning device. EPA says active systems must have a warning device, such as a liquid gauge, a sound alarm, a light indicator, or a dial or needle display. It must be placed where it can be seen or heard easily. EPA says the warning device is usually a manometer, which is a liquid gauge. Your mitigator should show you what a normal reading looks like for your system, so ask them to explain it and to give you written instructions.
  2. Listen and look at the fan area. Fans are commonly in an attic, a garage or outside. From a safe, easy spot, notice whether the fan is running or silent, whether it sounds different than before, and whether it vibrates. Do not open the fan housing or touch wiring.
  3. Check the power. See whether the switch or circuit breaker that feeds the fan has been turned off or has tripped. If a breaker keeps tripping, leave it and call a professional. Do not do electrical work on the fan or its wiring.
  4. Look for water or ice. If you see water, ice or frost on the fan or the vent pipe, take a photo and tell your mitigator. Do not chip at it, drill the pipe or change the pipe.
  5. Check that nothing has changed. Note any recent work on the home, such as remodeling, a new sump or pipe work that might have touched the system. EPA says to ask your contractor whether remodeling could void a warranty and to retest after remodeling.
  6. Write down what you saw. The reading on the warning device, the date, and any noise or visible change. This helps the mitigator.

Radon fans we see listed

Listings for reference. Fan selection depends on system design; a qualified radon mitigation professional sizes the fan. See the radon fan sizing guide.

What to leave to a professional

EPA recommends using a qualified radon mitigation contractor for radon reduction work. For a fan that is not working, that means a professional should:

  • Find out why the fan stopped or is acting differently.
  • Repair or replace the fan and check the electrical connections against local codes.
  • Confirm the warning device works.
  • Check that the system is venting properly above the roof.

If you are not sure who installed your system, check with your state radon office, which can often provide a list of qualified providers. The radon mitigation page lists where to start.

Retest after any repair

After a repair or replacement, CDC says to test radon levels again to be sure the repair worked. EPA says a post-mitigation test is best done as a two- to seven-day measurement with windows and doors closed 12 hours before and during the test, and it recommends an independent follow-up. EPA also says it is a good idea to retest at least every two years. See how to test for radon for the steps.

Reference levels for your retest

EPA recommends fixing a home at 4.0 pCi/L or higher and says to consider fixing between 2 and 4 pCi/L. The WHO reference level is 2.7 pCi/L (100 Bq/m3). See the radon levels chart for your result.

Frequently Asked Questions

What should I do first if I think my radon fan stopped?

Look at your warning device and check that the fan still has power. EPA says to look at the warning device on a regular basis and to call a contractor if it shows the system is not working properly. EPA also says the fan should never be turned off.

Can I replace a radon fan myself?

We recommend leaving fan service and replacement to a qualified professional. Radon fans are wired into the home's electrical system, and EPA says electrical connections must follow local electrical codes. EPA also says lowering radon levels takes technical knowledge and special skills.

What does it cost to have a radon fan replaced?

EPA says replacing a fan will cost around $200 to $350 including parts and labor. EPA also says the cost varies with labor and materials, so ask qualified mitigators for estimates before work begins. See the cost guide for more.

Do I need to retest after a radon fan is repaired or replaced?

Yes, testing again after repairs is the way to confirm the system is lowering radon. CDC says to test radon levels again after any repairs to be sure they worked. EPA also suggests retesting at least every two years.

Is a noisy radon fan a sign of a problem?

Not always, but a change in sound is worth mentioning. A fan that has become louder, rougher or quieter than you remember is something to describe to your mitigator. We do not have a sourced sound level to compare against, so we cannot say what is normal for your fan.

Sources

These sources describe warning devices, fan life, costs and retesting. We cite no numbers beyond what they state.