What to do with that: get written estimates from more than one qualified radon mitigation contractor, and compare what each quote includes. The checklist below shows what to ask.
What EPA says about cost
EPA's Consumer's Guide to Radon Reduction says radon reduction systems work, and that some systems can reduce radon levels in a home by up to 99 percent. The guide says most homes can be fixed for about the same cost as other common home repairs, and that your costs may vary depending on the size and design of your home and which radon reduction methods are needed. EPA's advice is to get an estimate from one or more qualified radon mitigation contractors.
The guide is written for people whose home tested at 4.0 pCi/L or higher, the level at which EPA recommends fixing a home. Radon levels below 4.0 pCi/L still carry some risk, and EPA notes that in many cases they may also be reduced. The World Health Organization sets its reference level at 2.7 pCi/L (100 Bq/m3). If your result is high and you are deciding what comes next, see what to do if your radon test is high, and for how levels compare across the country see radon levels by state.
What drives the cost
No two homes are the same, so the work in each quote differs. These are the factors EPA's guidance points to, and the questions each one raises for your estimate.
Foundation type
EPA groups homes by foundation: basement, slab-on-grade, or crawlspace. Each has its own set of methods, and some homes have more than one foundation type, for example a basement under part of the house and a crawlspace under the rest. In those homes EPA says a combination of techniques may be needed to bring levels below 4.0 pCi/L, which means more than one set of work in the quote.
What is under the slab
The number and location of suction pipes depends on how easily air can move through the crushed rock or soil under the slab and on the strength of the radon source. Often only a single suction point is needed. Some contractors run diagnostic tests, such as a soil communication test, to learn how air moves under the foundation. EPA notes that many contractors give free estimates but may charge a fee for diagnostic tests, so ask whether one is part of your quote.
System type
The method chosen, such as sub-slab suction, sump-hole suction, or a crawlspace membrane with suction, changes the materials and the labor. The next section describes the main types. EPA also says to consider operating costs, not only installation: a less expensive system may cost more to operate and maintain.
Home size and layout
EPA lists the size and design of the home among the things that affect cost. A larger home, or one with additions or separate foundation areas, may need more suction points or more than one method. Your contractor decides this from a visual inspection of the home and, where needed, diagnostic tests.
Pipe routing and fan location
EPA's checklist for checking a contractor's work says the exhaust pipe of a soil suction system must vent above the roof surface and 10 feet or more above the ground, and at least 10 feet away from windows, doors or other openings unless it vents at least 2 feet above them. The fan must not be located in or below a livable area, so common spots are attics, garages or the exterior of the home. How the pipe gets from the suction point to a compliant exhaust point is part of what your contractor prices.
Electrical work and warning device
Electrical connections of active systems must follow local electrical codes. A fan installed outside must meet local building codes for exterior use. EPA also says a warning device must be installed to alert you if an active system stops working properly, such as a liquid gauge, sound alarm, light indicator or dial. Ask how the quote handles wiring, permits and the warning device.
Testing after installation
EPA recommends a post-mitigation radon test within 30 days of installation, and no sooner than 24 hours after the system is running with the fan on. Ask whether your contractor's price includes a post-installation test, and see the section on what happens after installation.
Typical system types
These descriptions come from EPA's Consumer's Guide to Radon Reduction. We do not list a price for any of them, because we do not have a cited public source for one.
Active sub-slab suction (sub-slab depressurization)
EPA calls this the most common and usually the most reliable method for basement and slab-on-grade homes. One or more suction pipes go through the floor slab into the crushed rock or soil under it, and a vent fan draws radon from below the home and releases it outdoors. Variations include drain-tile suction, sump-hole suction (a capped sump can keep draining water while serving as the suction location), and block-wall suction for hollow block foundation walls, often combined with sub-slab suction.
Passive sub-slab suction
This is the same as active sub-slab suction without a fan, relying on natural pressure differences. EPA says it is usually associated with radon-resistant features in newly built homes and is generally not as effective at reducing high radon levels as the active type.
Crawlspace membrane with suction
For crawlspace homes, EPA describes covering the earth floor with a high-density plastic sheet and using a vent pipe and fan to draw radon from under the sheet. EPA calls this submembrane suction and says that, properly applied, it is the most effective way to reduce radon in crawlspace homes. Active crawlspace depressurization and crawlspace ventilation are other options EPA describes as less favorable, and either can increase energy costs.
Other methods
EPA describes sealing, house or room pressurization, heat recovery ventilation (HRV) and natural ventilation as techniques that can be used in any type of home. EPA does not recommend sealing alone, because by itself it has not been shown to lower radon levels significantly or consistently, though sealing makes other methods more effective and cost-efficient. HRVs can increase ventilation while recovering heat, and EPA says they may raise heating and cooling costs, though not as much as ventilation without heat recovery. Natural ventilation is described as only a temporary approach.
Ongoing costs
- Electricity and conditioned air. EPA says systems that use fans are more effective in reducing radon but will slightly increase your electric bill, and that most system types cause some loss of heated or cooled air.
- Fan replacement. EPA says fans may last five years or more, that manufacturer warranties tend not to exceed five years, and that a fan may then need repair or replacement. EPA's page on checking whether a system is working properly (updated 2026) gives the cost of replacing a fan as around $200 to $350 including parts and labor. See how long radon fans last and the radon fan sizing guide, and for fan options see choosing a radon fan.
- HRV filters. If your system includes an HRV, EPA's Consumer's Guide (2025 edition) says the filter should be changed twice a year and gives replacement filters as priced between $10 and $25.
- Retesting. EPA says it is a good idea to retest at least every two years to be sure radon levels remain low. Radon test kits and monitors have their own prices, which we do not list here. See how to choose a radon test kit.
Radon fans we see listed
Listings for reference. Fan selection depends on system design; a qualified radon mitigation professional sizes the fan. See the radon fan sizing guide.
Professional or do-it-yourself
EPA recommends that you have a qualified radon mitigation contractor fix your home, because lowering high radon levels takes specific technical knowledge and special skills. EPA says that without the proper equipment or technical knowledge you could increase your radon level or create other potential hazards and additional costs. If you still decide to do the work yourself, EPA says to get information on training courses from your state radon office.
How to compare quotes
EPA suggests choosing a radon contractor the way you would choose someone for other home repairs: get more than one estimate, ask for references, and contact some of them. Put the same questions to every contractor so the quotes can be compared on equal terms.
Certification and credentials
- Does the quote include proof of state certification, professional proficiency or certification credentials? Many states require radon professionals to be licensed, certified or registered. Your state radon office can tell you what applies.
- In states that do not regulate radon services, ask whether the contractor holds a proficiency or certification credential and follows industry standards such as ASTM E2121, the standard practice for installing radon mitigation systems in existing low-rise residential buildings.
- Is there proof of liability insurance, bonding and the licenses needed to satisfy local requirements?
Written scope
- Did the contractor inspect your home's structure and review your radon measurement results before giving an estimate?
- Is diagnostic testing included, or charged separately?
- Can the contractor explain what the work involves, how long it will take, and how the system will work?
- Does the written contract describe the work, the system components, the total cost including taxes and permit fees, any deposit, when payment is due, and the time needed to complete the work?
- Will the contractor obtain the permits and follow the required building codes?
Warranty and guarantee
- Is there a guarantee to reduce radon to 4.0 pCi/L or below, and for how long? EPA notes many contractors guarantee to adjust or modify the system to reach a negotiated level, so read the conditions of any guarantee carefully.
- What warranties apply to the hardware components, and are copies provided?
- Which optional extras, such as an extended warranty, a service plan or improved appearance, add to the price?
Post-install test
- Does the quote include testing after installation to make sure the system works?
- Is a warning device included?
- Will the contractor explain and demonstrate the system, and provide written operating and maintenance instructions?
EPA also says to weigh what you get for the money: a less expensive system may cost more to operate and maintain or have less appeal, a more expensive system may be best for your home, and the quality of the materials affects how long the system lasts.
After installation
EPA recommends a post-mitigation test within 30 days of installation, and no sooner than 24 hours after the system is operating with the fan on. The contractor may test their own work, but EPA recommends an independent follow-up measurement, either by an independent tester or by you, which avoids any conflict of interest. A two- to seven-day test is recommended, with windows and doors closed for 12 hours before and during the test except for normal entry and exit. For the steps, see how to test for radon. After that, check the warning device regularly and retest at least every two years, and after remodeling that changes the foundation or the lowest lived-in area.
Frequently Asked Questions
How much does a radon mitigation system cost?
It depends on your home. EPA says most homes can be fixed for about the same cost as other common home repairs, and that cost varies with the size and design of the home and the method needed. EPA does not publish an installation price range, and we have no other cited public source for one, so no sourced figure is available. Request written estimates from qualified contractors.
Why do radon mitigation quotes differ?
Quotes can differ in the foundation work, the system type, the number of suction points, the pipe route and fan location, electrical work, diagnostic testing, warranties, and whether testing after installation is included. Compare the written scope of each quote, not only the total.
How much does it cost to replace a radon fan?
EPA says replacing a fan will cost around $200 to $350 including parts and labor, and that fans may last five years or more. Get an estimate from a qualified mitigator before work begins. See how long radon fans last.
Can I install a radon mitigation system myself?
EPA recommends a qualified radon mitigation contractor, because the work takes specific technical knowledge and special skills, and mistakes could raise radon levels or create other hazards and additional costs. If you still plan to do it yourself, your state radon office can point you to training courses.
Do I need to test again after the system is installed?
Yes. EPA recommends a post-mitigation test within 30 days of installation, and retesting at least every two years afterward. Ask each contractor whether a post-installation test is part of the quote.
Sources
Every statement about cost, system types and contractor selection on this page comes from the sources below. Where a source gives no price, we do not give one.
- EPA, A Consumer's Guide to Radon Reduction (PDF, 2025 edition): cost statement, contractor checklist, system types, installation requirements and maintenance.
- EPA, How much can a radon mitigation system cost?: EPA's statement on mitigation costs.
- EPA, How do I know if my radon mitigation system is working properly? (updated 2026): warning devices, fan life, fan replacement cost and retesting.
- EPA, state radon contact information: where to find your state radon office and requirements for radon professionals.
- EPA, find a radon test kit or a measurement and mitigation professional: how to find qualified professionals and private proficiency programs.
- World Health Organization, Radon and health: the WHO reference level of 100 Bq/m3 (2.7 pCi/L).
- CDC, Radon: general radon information.