There is no single fan size that suits every home. The fan has to keep enough suction under the slab, and how much that takes depends on the soil or gravel under the slab, the size of the slab and the pipe it connects to. This page explains those factors in plain language. It gives no airflow, power or price numbers, because the sources it cites do not publish a sizing chart.
What the fan does in a soil suction system
EPA describes active subslab suction (also called subslab depressurization) as the most common and usually the most reliable radon reduction method. One or more suction pipes go through the floor slab into the crushed rock or soil underneath. A radon vent fan connected to the suction pipes draws radon gas from below the home and releases it into the outdoor air, while creating a negative pressure, or vacuum, beneath the slab.
EPA also says common fan locations include unconditioned home and garage spaces, such as attics, and the exterior of the home. The fan must not be located in or below a livable area.
What affects fan choice
These are the factors that decide how a fan and its pipes need to perform. The first two come from EPA. The last two are practical details a professional also takes into account.
- Suction under the slab. The fan has to create enough suction beneath the slab to draw soil gas toward the suction pipe. EPA calls this a negative pressure or vacuum beneath the slab.
- Soil and aggregate permeability. EPA says the number and location of suction pipes depends on how easily air can move in the crushed rock or soil under the slab. Open, gravel-like material lets suction spread easily. Tight soil does not.
- Strength of the radon source. EPA lists this alongside permeability as a deciding factor.
- Slab size and layout. A larger or more divided slab can need more suction points, or more suction, than a small open one.
- Pipe run. The length, routing and fittings of the pipe between the suction point and the vent above the roof affect how much work the fan has to do.
EPA notes that often only a single suction point is needed. Whether that is true for a given home is something the diagnostics show.
Radon fans we see listed
Listings for reference. Fan selection depends on system design; a qualified radon mitigation professional sizes the fan.
Diagnostics: how a professional checks suction
EPA says a contractor gets information about the home from visual inspection, from diagnostic tests, or from experience. One example in the Consumer's Guide is a soil communication test. A vacuum cleaner hose goes in one small hole and chemical smoke goes in a second small hole. If the smoke is pulled toward the vacuum, air can move easily under the foundation. Professionals sometimes call this kind of check pressure-field extension testing.
EPA says whether diagnostic tests are needed depends on details specific to your home, such as the foundation design, the material under the home, and the contractor's experience with similar homes. Many contractors give free estimates but may charge for diagnostic tests.
Why a certified professional sizes the fan
EPA recommends hiring a state-certified or otherwise qualified radon mitigation contractor. Many states require radon professionals to be licensed, certified or registered. Where a state does not, EPA suggests asking whether the contractor holds a professional proficiency or certification credential and follows industry consensus standards.
The EPA Consumer's Guide names ASTM E2121 as a standard practice for installing radon mitigation systems in existing low-rise residential buildings. AARST publishes ANSI/AARST SGM-SF-2023, Soil Gas Mitigation Standards for Existing Homes, whose scope is practices, minimum requirements and general guidance for reducing soil gas entry into existing homes. A professional who works to these standards, and to any state requirements, is the right person to size and install the fan.
We do not list airflow, wattage or price figures on this page. The sources we cite do not publish a sizing chart, and numbers copied from a product page would not tell you what your home needs.
Questions to ask your mitigator about the fan
- Did you inspect my home's structure before giving the estimate, and will you run diagnostic tests first?
- Where will the fan go, and does that location meet the EPA installation requirements?
- What warning device will be installed, and will you show me how to read it?
- Will you give me written operating and maintenance instructions and copies of any warranties?
- When will the post-mitigation test be done, and who will do it?
These come from the contractor checklist in EPA's Consumer's Guide. For typical costs, see the radon mitigation system cost guide.
After the fan is installed
EPA says a post-mitigation test should be done within 30 days of installation, but no sooner than 24 hours after the system is running with the fan on. A two- to seven-day measurement is recommended, with windows and doors closed 12 hours before and during the test. EPA recommends an independent follow-up measurement. It also says the fan should never be turned off, and that retesting at least every two years is a good idea.
Fan sizing only matters if mitigation is needed. EPA recommends fixing a home at 4.0 pCi/L or higher and says to consider fixing between 2 and 4 pCi/L. The WHO reference level is 2.7 pCi/L (100 Bq/m3). If you have not tested yet, start with the radon testing guide.
Frequently Asked Questions
Is there a standard radon fan size for a typical home?
No single size fits every home. EPA says the number and location of suction points depends on how easily air moves in the crushed rock or soil under the slab and on the strength of the radon source. A certified mitigation professional works that out for each home. See the radon fan guide for how fans are used in these systems.
Can I choose a radon fan myself from the specifications?
EPA recommends that a qualified radon mitigation contractor fix your home, because lowering high radon levels requires specific technical knowledge and special skills. Fan choice depends on diagnostics done in your home, so it is a job for the professional who designs and installs the system.
What is a pressure-field extension test?
It is a diagnostic check of how far suction reaches under the slab. EPA describes a version of it as a soil communication test, in which a vacuum cleaner and chemical smoke show how easily air moves from one point to another under the foundation. Professionals sometimes call this kind of check pressure-field extension testing.
Does a bigger fan always work better?
We do not have a source that says so, and EPA does not publish a fan sizing chart. EPA says fan placement and system design must follow the installation requirements in its Consumer's Guide, and that the system should be checked with a post-mitigation test. The test result, not the fan label, shows whether the system is working.
How do I know the fan I have is doing its job?
Look at the warning device regularly, and retest. EPA says to check the warning device (usually a manometer) on a regular basis, to run a post-mitigation test, and to retest at least every two years. If the warning device shows a problem, call a mitigator. See radon fan not working.
Sources
Every statement above about how systems work or what EPA recommends comes from these sources. The standards are named for context, and we describe only their published scope.
- EPA, Consumer's Guide to Radon Reduction (PDF): how radon reduction systems work, hiring a contractor, and maintaining a system.
- AARST, ANSI/AARST SGM-SF-2023: Soil Gas Mitigation Standards for Existing Homes: the standard's published scope: practices, minimum requirements and general guidance for reducing soil gas entry into existing homes.
- EPA, How do I know if my radon mitigation system is working properly?: soil suction, warning devices, fan life, and retesting.
- EPA, How much can a radon mitigation system cost?: EPA's statement on mitigation costs.
- EPA, What is EPA's Action Level for Radon and What Does it Mean?: the 4 pCi/L action level, the 2 to 4 pCi/L range, and average indoor radon.
- EPA, Does the 2009 WHO recommendation affect EPA's action level?: how EPA describes the WHO reference level of 2.7 pCi/L.
- EPA, Find a Radon Test Kit or Measurement and Mitigation Professional: where to get test kits and how to find qualified radon service providers.